To wind a Vostok Europe automatic watch, unscrew the screw-down crown counterclockwise, leave it in Position 0 and turn it clockwise until the watch starts running. Wearing the watch then keeps it wound. Whenever the clocks change for daylight saving time, or the watch stops after a few days in a drawer, it helps to know your automatic well: how it keeps running, how to wind it by hand, how to set the time and date without damaging anything and what to do if it stops overnight. This guide covers all of it, with the Vostok Europe Energia Bronze YN84-575O540 as our prime example!

How an automatic watch keeps running
An automatic watch is a mechanical watch that winds itself. Inside is a mainspring, a coiled spring that stores energy and releases it slowly to drive the hands. A semicircular weight called the rotor spins as your wrist moves and winds that spring a little with every movement.
The amount of energy the mainspring can hold is the power reserve: how long the watch keeps running after you take it off. The automatic watch power reserve on the movements in this guide is around 40 hours or more, so a watch worn all day will usually run through the night and into the next morning. If it sits unworn for a weekend, it will stop, and that is completely normal.
How to wind an automatic watch by hand
Winding by hand is useful when the watch has stopped, or when you want a full reserve before you put it on. Here is how to do it:
- Take the watch off your wrist, so you don't strain the crown at an angle.
- Unscrew the screw-down crown counterclockwise until it springs out. This is Position 0. Do not pull it any further.
- With the crown in Position 0, turn it clockwise with gentle, even turns. You may feel or hear a soft winding action.
- Keep turning until the seconds hand starts to move. If the watch hasn't been worn recently, we recommend about 55 turns in total for a full wind.
- Set the time if needed (see below), then push the crown back in and screw it down gently clockwise until it is snug. Never force it.
A screw-down crown is a crown that seals against the case with a thread, an important part of how many dive watches keep water out. Always make sure it is fully screwed down before any contact with water, and never operate the crown underwater or when the watch is wet. For more on how crowns and gaskets work with water ratings, see our guide to water resistance ratings.

Can you overwind an automatic watch?
No. Automatic movements are built so that the mainspring can't be overwound. Once it is fully wound, a slipping mechanism lets it slide instead of tightening further, so extra turns of the crown or extra wrist movement don't harm it. Just turn the crown gently and don't force it at an angle.
How to set the time and date
Our automatic watches use two crown layouts, depending on the movement. In both, the seconds hand stops when you pull the crown to the time-setting position, so you can set the time to the second:
- TMI NH-series (such as the NH35 and NH34), 3 positions: Position 0 for winding, Position 1 for the date (turn counterclockwise) or, on the NH34, the GMT hand (turn clockwise), and Position 2 for the time.
- S. Epson YN84 (Energia Bronze), 2 positions: Position 0 for winding and Position 1 for the time.
Avoid the date-change danger zone
Here is the most important rule for how to change the date on a watch: don't set the date while the watch shows a time between 9 p.m. and 4 a.m. Adjusting the date in this window can cause a malfunction, because the date mechanism is already preparing for the change at midnight. The safe method is to set the hands outside this range first, for example to around 6 o'clock, then set the date, then set the correct time.
Setting the time for daylight saving
When the clocks go back in the fall, pull the crown to the time-setting position and move the hands back one hour. In the spring, move them forward one hour instead. If the hands pass midnight, check the date afterwards. Then push the crown in and screw it down.
Reading the power reserve
Some automatic watches show you how much energy is left in the mainspring. The Energia Bronze YN84-575O540 has a power reserve indicator on the dial, so you can see at a glance whether the watch needs a few turns of the crown or a day on the wrist.

The Energia Bronze runs on the S. Epson YN84 automatic movement with 22 jewels and a power reserve of 40+ hours. Its functions cover hours, minutes, seconds, the power reserve indicator and a 24-hour indicator. It has no date display, so after winding you only need to set the time. Its crown has two positions: Position 0 for winding and Position 1 for the time. The 24-hour indicator turns with the hour hand and can't be set separately, so use it to tell a.m. from p.m. when you set the time. A full power reserve of about 40 hours takes around 55 crown turns or several hours of active wear. The 48 x 17.3 mm case is made of bronze, which develops its own patina over time. Our guide to bronze case watches explains what to expect.
The watch is rated to 300 m (30 bar) and has a 3.5 mm K1 crystal with anti-reflective coating and Swiss-made tritium tubes in metal reflectors. It comes with genuine leather and silicone straps in a VE Dry Box XL. It is limited to 3,000 pieces.

| Energia Bronze YN84-575O540 | Spec |
|---|---|
| Movement | S. Epson YN84 automatic (Japan), 22 jewels, 40+ hours power reserve |
| Functions | Hours, minutes, seconds, power reserve indicator, 24-hour indicator |
| Case | 48 x 17.3 mm, bronze, lug-to-lug 60.2 mm |
| Crystal | 3.5 mm K1, anti-reflective coating |
| Water resistance | 300 m / 30 bar |
| Illumination | Swiss-made tritium tubes in metal reflectors |
| Straps | Genuine leather and silicone, VE Dry Box XL |
| Edition | Limited to 3,000 pieces |
Watch the rotor work
If you'd like to see the automatic mechanism in action, the Energia NH35A-575E651 has an exhibition caseback with screws. Turn it over and you can watch the rotor swing as you move your wrist. It runs on the TMI NH35 automatic movement with 24 jewels and a power reserve of 41+ hours, with a beige dial and a blue PVD case with rose gold PVD bezel and crown. It is rated to 300 m (30 bar).

If you don't wear it every day
An automatic watch stopped overnight or over a weekend is not broken. It has simply used up its power reserve. To restart it:
- Wind it by hand with about 55 turns of the crown.
- If your watch has a date, set it first, outside the 9 p.m. to 4 a.m. window.
- Set the time, push the crown back in and screw it back down gently.
If you rotate between several watches, you can store an automatic face up in a box, or use a watch winder if you prefer to keep it running. Both are fine. Letting an automatic stop now and then does it no harm.

Still deciding between movement types? Our comparison of automatic vs quartz dive watches explains the pros of each.
Frequently asked questions
How long do you have to wear an automatic watch to fully wind it?
We recommend wearing an automatic for at least 10 hours a day to keep it wound. A full power reserve takes about 55 crown turns or several hours of active wear. If you spend most of the day at a desk, we recommend about 10 to 15 crown turns every day.
Can you manually wind all automatic watches?
Most modern automatics can be wound by hand, including the S. Epson YN84 in the Energia Bronze and the TMI NH35 in watches such as the Batiscafos NH35-511E768. A few automatic movements can't, so check the manual for your watch.
Do automatic watches need to be worn all the time?
No, but to keep it running, we recommend at least 10 hours of wear a day. If it stops, wind it with about 55 turns, set the time and it is ready to wear again.
Is setting an automatic GMT watch different?
The crown works the same way, with one extra step: on the TMI NH34, at Position 1 (first click), turning the crown clockwise sets the 24-hour hand and turning it counterclockwise sets the date. Our GMT watch guide explains the order.
How to wind an automatic watch: the short version
Unscrew the crown, turn it clockwise until the watch runs, set the date (if your watch has one) outside the 9 p.m. to 4 a.m. window, set the time and screw the crown back down. Wear the watch regularly and it keeps itself wound. With a service by an authorized technician every 2 years after the warranty period, our automatic watches are built to run accurately and reliably for 10 years or more.
Explore the Energia Bronze
See the full details of the Energia Bronze YN84-575O540 or browse the full Energia collection.